Engineering Design Process with Autodesk Fusion Quiz Answer. In this post you will get Quiz & Assignment Answer Of Engineering Design Process with Autodesk Fusion
Engineering Design Process with Autodesk Fusion Quiz
Offered By ”Autodesk”
Week 1 quiz
1.
Question 1
Mass properties are based
on?
1 point
- Solid geometry.
- Surface geometry.
- Physical material.
- Appearance.
2.
Question 2
True or false: When a comment is added to
a design, the file is automatically saved.
1 point
- True
- False
3.
Question 3
Section view is placed in
what folder in the browser?
1 point
- Analysis.
- Section.
- Origin.
- Construction.
4.
Question 4
Sketch slice, from the
sketch palette, is what?
1 point
- A trim tool for lines.
- Intersection curve in a sketch.
- Section view inside a sketch.
5.
Question 5
What sketch tool would you
used to create a circumscribed octagon?
1 point
- Line.
- Circle.
- Polygon.
- Rectangle.
Week 2 quiz
1.
Question 1
In the simulation workspace
in the Solve drop down menu, what icon will be used when the study is not ready
to solve?
1 point
Red X.
Green check mark.
Yellow exclamation mark.
2.
Question 2
True or false: Study material is the same
as a physical material applied in the model workspace.
1 point
True
False
3.
Question 3
Cloud credits allow you to
purchase the use of cloud processing for things like Renders and what else?
1 point
Exploded view animation.
Saving to STL.
Creating a 2D drawing.
Solving simulation.
4.
Question 4
Which of the following is a
good use of the Press/Pull tool?
1 point
Changing the diameter of a hole.
Deleting a face.
Adding a fillet to a part.
Changing the thickness of a
part.
5.
Question 5
In simulation results what
tool is used to find the stress value at a specific location?
1 point
Probe.
Point value.
Measure.
Local value.
Week 3 quiz
1.
Question 1
When creating a joint you
must select each component based on their what?
1 point
Type of motion.
Aligned position.
Physical material.
Center of mass.
2.
Question 2
True or false: Contact sets
account for gravity.
1 point
True
False
3.
Question 3
What is the difference
between a rigid joint and a rigid group?
1 point
Relative motion.
There is no difference.
The number of components.
4.
Question 4
A motion link is a type of
joint that allows the motion from one joint to control what?
1 point
The motion of a chain.
The time it takes to solve a joint.
The thickness of an extrude.
The motion of another joint.
5.
Question 5
True or false: A motion study
can be edited after its creation.
1 point
True
False
Week 4 quiz
1.
Question 1
What is it called to make a
component stationary with no joints applied?
1 point
Locate.
Ground.
Lock.
Fix.
2.
Question 2
A sketch spline has handles
that control influence or weight of curvature and what?
1 point
Series of curvature.
Direction of curvature.
Class of curvature.
G value.
3.
Question 3
A sweep surface requires at
least what?
1 point
Two profiles.
A profile and a path.
Two profiles and a path.
A profile.
4.
Question 4
What option controls the number
of triangles in an STL file?
1 point
Appearance
Resolution
Structure
Scale
5.
Question 5
What
do you need to convert a set of surfaces to a solid?
1 point
Extrude surface.
Thicken.
Extend surface.
Stitch a water tight set of surfaces.
Course assessment
1.
Question 1
Mass properties take the
mass of an applied material and multiply it by the what?
1 point
Solid volume.
Number of features.
Universal constant.
Conversion factor.
2.
Question 2
When sketching a center
point slot there are 3 points you must define.
What are they?
1 point
Slot midpoint.
Slot diameter point.
End center point.
Start center point.
3.
Question 3
When creating an extrude,
what is the default operation setting if the extrude intersects a solid body?
1 point
Join
New body
Cut
New component
4.
Question 4
If you want to place a
constraint that keeps two lines at 90 degrees, which one would you apply?
1 point
Perpendicular.
Parallel.
Coincident.
Midpoint.
5.
Question 5
Creating a section view can
be found on what menu?
1 point
Insert
Inspect
Assemble
Modify
6.
Question 6
Holding the CTRL key during
sketch creation does what?
1 point
Makes it horizontal.
Overrides persistent constraints.
Applies a standard dimension.
Ends the selection.
7.
Question 7
By default the colorbar
ranges from blue to what color in simulation results?
1 point
Green
Black
Yellow
Red
8.
Question 8
What would prompt you to
regenerate a mesh in a simulation?
1 point
Model changes.
Higher resolution needed.
Change of loads.
Change of constraints.
9.
Question 9
A contact set in an
assembly is used to?
1 point
Check electrical resistance.
Replicate physical interaction between solids.
Generate an interference report.
10.
Question 10
Which workspace would you
use to create a copy of an imported face?
1 point
Model
Sculpt
Patch
Render
Peer-graded Assignment: Perform a static simulation study.